mpconfigboard.h 2.58 KB
Newer Older
1
2
3
4
#define MICROPY_HW_BOARD_NAME       "Espruino Pico"
#define MICROPY_HW_MCU_NAME         "STM32F401CD"
#define MICROPY_PY_SYS_PLATFORM     "pyboard"

5
6
7
#define MICROPY_PY_USOCKET          (0)
#define MICROPY_PY_NETWORK          (0)

8
#define MICROPY_HW_HAS_SWITCH       (1)
9
#define MICROPY_HW_HAS_FLASH        (1)
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
#define MICROPY_HW_HAS_SDCARD       (0)
#define MICROPY_HW_HAS_MMA7660      (0)
#define MICROPY_HW_HAS_LIS3DSH      (0)
#define MICROPY_HW_HAS_LCD          (0)
#define MICROPY_HW_ENABLE_RNG       (0)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_TIMER     (1)
#define MICROPY_HW_ENABLE_SERVO     (1)
#define MICROPY_HW_ENABLE_DAC       (0)
#define MICROPY_HW_ENABLE_CAN       (0)

// Pico has an 8 MHz HSE and the F401 does 84 MHz max
#define MICROPY_HW_CLK_PLLM (5)
#define MICROPY_HW_CLK_PLLN (210)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV4)
#define MICROPY_HW_CLK_PLLQ (7)

// does not have a 32kHz crystal
#define MICROPY_HW_RTC_USE_LSE      (0)

30
31
32
33
34
35
36
37
38
39
// UART config
#define MICROPY_HW_UART1_PORT (GPIOB)
#define MICROPY_HW_UART1_PINS (GPIO_PIN_6 | GPIO_PIN_7)
#define MICROPY_HW_UART2_PORT (GPIOA)
#define MICROPY_HW_UART2_PINS (GPIO_PIN_2 | GPIO_PIN_3)
#define MICROPY_HW_UART2_RTS  (GPIO_PIN_1)
#define MICROPY_HW_UART2_CTS  (GPIO_PIN_0)
#define MICROPY_HW_UART6_PORT (GPIOA)
#define MICROPY_HW_UART6_PINS (GPIO_PIN_11 | GPIO_PIN_12)

40
41
42
43
44
45
46
47
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B6)
#define MICROPY_HW_I2C1_SDA (pin_B7)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B3)
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_B4)

48
49
50
51
52
53
54
55
56
57
// SPI busses
#define MICROPY_HW_SPI1_NSS  (pin_A4)
#define MICROPY_HW_SPI1_SCK  (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI2_NSS  (pin_B12)
#define MICROPY_HW_SPI2_SCK  (pin_B13)
#define MICROPY_HW_SPI2_MISO (pin_B14)
#define MICROPY_HW_SPI2_MOSI (pin_B15)

58
59
60
61
62
63
64
65
66
67
68
69
70
71
// BTN1 has no pullup or pulldown; it is active high and broken out on a header
#define MICROPY_HW_USRSW_PIN        (pin_C13)
#define MICROPY_HW_USRSW_PULL       (GPIO_PULLDOWN)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED    (1)

// Pico has 2 LEDs
#define MICROPY_HW_LED1             (pin_B2)  // red
#define MICROPY_HW_LED2             (pin_B12) // green
#define MICROPY_HW_LED3             (pin_B12) // green
#define MICROPY_HW_LED4             (pin_B12) // green
#define MICROPY_HW_LED_OTYPE        (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin)      (pin->gpio->BSRRL = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin)     (pin->gpio->BSRRH = pin->pin_mask)