mpconfigboard.h 2.67 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
#define MICROPY_HW_BOARD_NAME       "NUCLEO-F429ZI"
#define MICROPY_HW_MCU_NAME         "STM32F429"

#define MICROPY_HW_HAS_SWITCH       (1)
#define MICROPY_HW_HAS_FLASH        (1)
#define MICROPY_HW_HAS_SDCARD       (0)
#define MICROPY_HW_HAS_MMA7660      (0)
#define MICROPY_HW_HAS_LIS3DSH      (0)
#define MICROPY_HW_HAS_LCD          (0)
#define MICROPY_HW_ENABLE_RNG       (1)
#define MICROPY_HW_ENABLE_RTC       (1)
#define MICROPY_HW_ENABLE_TIMER     (1)
#define MICROPY_HW_ENABLE_SERVO     (0)
#define MICROPY_HW_ENABLE_DAC       (0)
#define MICROPY_HW_ENABLE_CAN       (1)

// HSE is 8MHz
#define MICROPY_HW_CLK_PLLM (8)
#define MICROPY_HW_CLK_PLLN (180)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV2)
#define MICROPY_HW_CLK_PLLQ (4)

// From the reference manual, for 2.7V to 3.6V
// 151-180 MHz => 5 wait states
// 181-210 MHz => 6 wait states
// 211-216 MHz => 7 wait states
#define MICROPY_HW_FLASH_LATENCY    FLASH_LATENCY_6

// UART config
#define MICROPY_HW_UART1_TX     (pin_A9)
#define MICROPY_HW_UART1_RX     (pin_A10)

#define MICROPY_HW_UART2_TX     (pin_D5)
#define MICROPY_HW_UART2_RX     (pin_D6)

#define MICROPY_HW_UART3_TX     (pin_D8)
#define MICROPY_HW_UART3_RX     (pin_D9)

#define MICROPY_HW_UART4_TX     (pin_A0)
#define MICROPY_HW_UART4_RX     (pin_C11)

#define MICROPY_HW_UART5_TX     (pin_C12)
#define MICROPY_HW_UART5_RX     (pin_D2)

#define MICROPY_HW_UART_REPL        PYB_UART_3
#define MICROPY_HW_UART_REPL_BAUD   115200

// I2C busses
#define MICROPY_HW_I2C3_SCL (pin_A8)
#define MICROPY_HW_I2C3_SDA (pin_C9)

// SPI busses
#define MICROPY_HW_SPI1_NSS     (pin_A4)
#define MICROPY_HW_SPI1_SCK     (pin_B3)
#define MICROPY_HW_SPI1_MISO    (pin_B4)
#define MICROPY_HW_SPI1_MOSI    (pin_B5)

#define MICROPY_HW_SPI4_NSS     (pin_E4)
#define MICROPY_HW_SPI4_SCK     (pin_E2)
#define MICROPY_HW_SPI4_MISO    (pin_E5)
#define MICROPY_HW_SPI4_MOSI    (pin_E6)

#define MICROPY_HW_SPI5_NSS     (pin_F6)
#define MICROPY_HW_SPI5_SCK     (pin_F7)
#define MICROPY_HW_SPI5_MISO    (pin_F8)
#define MICROPY_HW_SPI5_MOSI    (pin_F9)

// USRSW is pulled low. Pressing the button makes the input go high.
#define MICROPY_HW_USRSW_PIN        (pin_C13)
#define MICROPY_HW_USRSW_PULL       (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE  (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED    (1)

// LEDs
#define MICROPY_HW_LED1             (pin_B0) // green
#define MICROPY_HW_LED2             (pin_B7) // blue
#define MICROPY_HW_LED3             (pin_B14) // red
#define MICROPY_HW_LED_ON(pin)      (mp_hal_pin_high(pin))
#define MICROPY_HW_LED_OFF(pin)     (mp_hal_pin_low(pin))

// USB config (CN13 - USB OTG FS)
#define MICROPY_HW_USB_VBUS_DETECT_PIN (pin_A9)
#define MICROPY_HW_USB_OTG_ID_PIN      (pin_A10)