usb_bsp.c 7.46 KB
Newer Older
Damien's avatar
Damien committed
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
/**
  ******************************************************************************
  * @file    usb_bsp.c
  * @author  MCD Application Team
  * @version V1.1.0
  * @date    19-March-2012
  * @brief   This file is responsible to offer board support package and is 
  *          configurable by user.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */ 

/* Includes ------------------------------------------------------------------*/
30
#include "stm_misc.h"
Damien's avatar
Damien committed
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
#include "stm32f4xx_gpio.h"
#include "stm32f4xx_rcc.h"
#include "usb_bsp.h"

/** @addtogroup STM32_USB_OTG_DEVICE_LIBRARY
* @{
*/

/** @defgroup USB_BSP
* @brief This file is responsible to offer board support package
* @{
*/ 

/** @defgroup USB_BSP_Private_Defines
* @{
*/ 
/**
* @}
*/ 


/** @defgroup USB_BSP_Private_TypesDefinitions
* @{
*/ 
/**
* @}
*/ 





/** @defgroup USB_BSP_Private_Macros
* @{
*/ 
/**
* @}
*/ 

/** @defgroup USBH_BSP_Private_Variables
* @{
*/ 

/**
* @}
*/ 

/** @defgroup USBH_BSP_Private_FunctionPrototypes
* @{
*/ 
/**
* @}
*/ 

/** @defgroup USB_BSP_Private_Functions
* @{
*/ 


/**
* @brief  USB_OTG_BSP_Init
*         Initilizes BSP configurations
* @param  None
* @retval None
*/

void USB_OTG_BSP_Init(USB_OTG_CORE_HANDLE *pdev) {
    RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);

100
    /* Configure DM DP Pins on PA11 and PA12 */
Damien's avatar
Damien committed
101
102
103
104
105
106
107
108
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11 | GPIO_Pin_12;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
    GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

109
110
    GPIO_PinAFConfig(GPIOA, GPIO_PinSource11, GPIO_AF_OTG_FS);
    GPIO_PinAFConfig(GPIOA, GPIO_PinSource12, GPIO_AF_OTG_FS);
Damien's avatar
Damien committed
111

112
    /* Configure VBUS Pin on PA9 (or disable VBUS_SENSING_ENABLED) */
Damien's avatar
Damien committed
113
114
115
116
117
118
119
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
    GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
    GPIO_Init(GPIOA, &GPIO_InitStructure);

120
    // Configure ID pin on PA10
121
122
123
124
125
126
127
128
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
    GPIO_InitStructure.GPIO_OType = GPIO_OType_OD;
    GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP ;
    GPIO_Init(GPIOA, &GPIO_InitStructure);
    GPIO_PinAFConfig(GPIOA, GPIO_PinSource10, GPIO_AF_OTG_FS);

Damien's avatar
Damien committed
129
130
131
132
133
134
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
    RCC_AHB2PeriphClockCmd(RCC_AHB2Periph_OTG_FS, ENABLE);
}

/**
* @brief  USB_OTG_BSP_EnableInterrupt
135
*         Enable USB Global interrupt
Damien's avatar
Damien committed
136
137
138
139
* @param  None
* @retval None
*/
void USB_OTG_BSP_EnableInterrupt(USB_OTG_CORE_HANDLE *pdev) {
140
    // this assumes we use NVIC_PriorityGroup_4
Damien's avatar
Damien committed
141
142
    NVIC_InitTypeDef NVIC_InitStructure;
    NVIC_InitStructure.NVIC_IRQChannel = OTG_FS_IRQn;
143
144
    NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 8;
    NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
Damien's avatar
Damien committed
145
146
147
148
    NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
    NVIC_Init(&NVIC_InitStructure);
}

149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
/**
* @brief  BSP_Drive_VBUS
*         Drives the Vbus signal through IO
* @param  state : VBUS states
* @retval None
*/

void USB_OTG_BSP_DriveVBUS(USB_OTG_CORE_HANDLE *pdev, uint8_t state) {
    //printf("DriveVBUS %p %u\n", pdev, state);
    /*
    On-chip 5 V VBUS generation is not supported. For this reason, a charge pump 
    or, if 5 V are available on the application board, a basic power switch, must 
    be added externally to drive the 5 V VBUS line. The external charge pump can 
    be driven by any GPIO output. When the application decides to power on VBUS 
    using the chosen GPIO, it must also set the port power bit in the host port 
    control and status register (PPWR bit in OTG_FS_HPRT).

    Bit 12 PPWR: Port power
    The application uses this field to control power to this port, and the core 
    clears this bit on an overcurrent condition.
    */
#if 0 // not implemented
#ifndef USE_USB_OTG_HS
    if (0 == state) {
        /* DISABLE is needed on output of the Power Switch */
        GPIO_SetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
    } else {
        /*ENABLE the Power Switch by driving the Enable LOW */
        GPIO_ResetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
    }
#endif
#endif
}

/**
  * @brief  USB_OTG_BSP_ConfigVBUS
  *         Configures the IO for the Vbus and OverCurrent
  * @param  None
  * @retval None
  */

void  USB_OTG_BSP_ConfigVBUS(USB_OTG_CORE_HANDLE *pdev) {
    //printf("ConfigVBUS %p\n", pdev);
#if 0 // not implemented
#ifdef USE_USB_OTG_FS   
  GPIO_InitTypeDef GPIO_InitStructure; 
  
#ifdef USE_STM3210C_EVAL
  RCC_APB2PeriphClockCmd(HOST_POWERSW_PORT_RCC, ENABLE);
  
  
  /* Configure Power Switch Vbus Pin */
  GPIO_InitStructure.GPIO_Pin = HOST_POWERSW_VBUS;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
  GPIO_Init(HOST_POWERSW_PORT, &GPIO_InitStructure);
#else
  #ifdef USE_USB_OTG_FS  
  RCC_AHB1PeriphClockCmd( RCC_AHB1Periph_GPIOH , ENABLE);  
  
  GPIO_InitStructure.GPIO_Pin = HOST_POWERSW_VBUS;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
  GPIO_Init(HOST_POWERSW_PORT,&GPIO_InitStructure);
  #endif  
#endif

  /* By Default, DISABLE is needed on output of the Power Switch */
  GPIO_SetBits(HOST_POWERSW_PORT, HOST_POWERSW_VBUS);
  
  USB_OTG_BSP_mDelay(200);   /* Delay is need for stabilising the Vbus Low 
  in Reset Condition, when Vbus=1 and Reset-button is pressed by user */
#endif  
#endif
}

Damien's avatar
Damien committed
227
228
229
230
231
232
233
234
235
/**
* @brief  USB_OTG_BSP_uDelay
*         This function provides delay time in micro sec
* @param  usec : Value of delay required in micro sec
* @retval None
*/
void USB_OTG_BSP_uDelay (const uint32_t usec)
{
  uint32_t count = 0;
236
  const uint32_t utime = (168 * usec / 5);
Damien's avatar
Damien committed
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
  do
  {
    if ( ++count > utime )
    {
      return ;
    }
  }
  while (1);
}


/**
* @brief  USB_OTG_BSP_mDelay
*          This function provides delay time in milli sec
* @param  msec : Value of delay required in milli sec
* @retval None
*/
void USB_OTG_BSP_mDelay (const uint32_t msec)
{
  USB_OTG_BSP_uDelay(msec * 1000);   
}
/**
* @}
*/ 

/**
* @}
*/ 

/**
* @}
*/

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/