po_hi_driver_linux_serial.c 12.8 KB
Newer Older
1
2
3
4
5
/*
 * This is a part of PolyORB-HI-C distribution, a minimal
 * middleware written for generated code from AADL models.
 * You should use it with the Ocarina toolsuite.
 *
6
7
8
 * For more informations, please visit http://ocarina.enst.fr
 *
 * Copyright (C) 2010, European Space Agency (ESA).
9
10
 */

11
12
#include <drivers/po_hi_driver_linux_serial.h>

13
14
15
#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_SENDER) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_RECEIVER)
16

17
#define __PO_HI_DRIVER_SERIAL_LINUX_BAUDRATE B19200
18
19

#include <po_hi_debug.h>
20
#include <po_hi_utils.h>
21
22
#include <po_hi_messages.h>
#include <po_hi_transport.h>
23
#include <po_hi_gqueue.h>
24
25
/* po-hi-c related files */

26
27
28
29
30
#include <activity.h>
#include <marshallers.h>
#include <deployment.h>
/* generated files */

31
32
33
34
#include <termios.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
35
#include <unistd.h>
36
37
38
#include <strings.h>
/* Linux-specific files */

39
40
int po_hi_c_driver_serial_fd_read;
int po_hi_c_driver_serial_fd_write;
41

42
43
#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_RECEIVER)
44
45
46

void __po_hi_c_driver_serial_linux_poller (void)
{
47
48
49
   int n;
   int ts;

50
51
   unsigned long* swap_pointer;
   unsigned long swap_value;
52

53
54
   __po_hi_msg_t msg;
   __po_hi_request_t request;
55

56
   __PO_HI_DEBUG_DEBUG ("[LINUX SERIAL] Hello, i'm the serial poller , must read %d bytes!\n", __PO_HI_MESSAGES_MAX_SIZE);
57
58

   __po_hi_msg_reallocate (&msg);
59

60
   n = read (po_hi_c_driver_serial_fd_read, &(msg.content[0]), __PO_HI_MESSAGES_MAX_SIZE); 
61

62
#ifdef __PO_HI_DEBUG_INFO
63
   __PO_HI_DEBUG_INFO  ("[LINUX SERIAL] Message: 0x");
64
65
66

   for (ts = 0 ; ts < __PO_HI_MESSAGES_MAX_SIZE ; ts++)
   {
67
      __PO_HI_DEBUG_INFO ("%x", msg.content[ts]);
68
   }
69
   __PO_HI_DEBUG_INFO ("\n");
70
#endif
71
72
   
   if (n == -1)
73
   {
74
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Cannot read on socket !\n");
75
      return;
76
   }
77

78
79
80
81
82
   if (n == 0)
   {
      return;
   }

83

84
   __PO_HI_DEBUG_DEBUG ("[LINUX SERIAL] read() returns %d\n", n);
85

86
   msg.length = n;
87

88
89
90
   swap_pointer  = (unsigned long*) &msg.content[0];
   swap_value    = *swap_pointer;
   *swap_pointer = __po_hi_swap_byte (swap_value);
91

92
#ifdef __PO_HI_DEBUG_INFO
93
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Message after swapped port: 0x");
94
   for (ts = 0 ; ts < msg.length ; ts++)
95
   {
96
        __PO_HI_DEBUG_INFO ("%x", msg.content[ts]);
97
   }
98
   __PO_HI_DEBUG_INFO ("\n");
99

100
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Received: %s\n", msg.content);
101
#endif
102

103
104
   __po_hi_unmarshall_request (&request, &msg);

105
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Destination port: %d\n", request.port);
106
   __po_hi_main_deliver (&request);
107
}
108
109
110
111
112
113
114
115
116
117
#endif


#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_SENDER)

void __po_hi_c_driver_serial_linux_init_sender (__po_hi_device_id id)
{
   struct termios oldtio,newtio;

118
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Init\n");
119
120
121
122
123

   po_hi_c_driver_serial_fd_write = open( __po_hi_get_device_naming (id), O_RDWR | O_NOCTTY | O_NONBLOCK);

   if (po_hi_c_driver_serial_fd_write < 0)
   {
124
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error while opening device %s\n", __po_hi_get_device_naming (id));
125
126
127
   }
   else
   {
128
      __PO_HI_DEBUG_DEBUG ("[LINUX SERIAL] Device successfully opened, fd=%d\n", po_hi_c_driver_serial_fd_write);
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
   }

   tcgetattr (po_hi_c_driver_serial_fd_write, &oldtio);  /* save current serial port settings */
   bzero (&newtio, sizeof(newtio));                /* clear struct for new port settings */
        
   /* 
    * BAUDRATE: Set bps rate. You could also use cfsetispeed and cfsetospeed.
    * CRTSCTS : output hardware flow control (only used if the cable has
    *           all necessary lines. See sect. 7 of Serial-HOWTO)
    * CS8     : 8n1 (8bit,no parity,1 stopbit)
    * CLOCAL  : local connection, no modem contol
    * CREAD   : enable receiving characters
    */

   newtio.c_cflag = __PO_HI_DRIVER_SERIAL_LINUX_BAUDRATE | CRTSCTS | CS8 | CLOCAL | CREAD;
         
   /*
    *  IGNPAR  : ignore bytes with parity errors
    *  ICRNL   : map CR to NL (otherwise a CR input on the other computer
    *            will not terminate input) otherwise make device raw 
    *            (no other input processing)
    */
   newtio.c_iflag = IGNPAR | ICRNL;
         
   /*
    * Raw output.
    */
   newtio.c_oflag = 1;
         
   /*
    * ICANON  : enable canonical input
    * disable all echo functionality, and don't send signals to calling program
    */
   newtio.c_lflag = ICANON;
163

164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
   /* 
    * Initialize all control characters 
    * default values can be found in /usr/include/termios.h, and are given
    * in the comments, but we don't need them here.
    */
   newtio.c_cc[VINTR]    = 0;     /* Ctrl-c */ 
   newtio.c_cc[VQUIT]    = 0;     /* Ctrl-\ */
   newtio.c_cc[VERASE]   = 0;     /* del */
   newtio.c_cc[VKILL]    = 0;     /* @ */
   newtio.c_cc[VEOF]     = 4;     /* Ctrl-d */
   newtio.c_cc[VTIME]    = 0;     /* inter-character timer unused */
   newtio.c_cc[VMIN]     = 1;     /* blocking read until 1 character arrives */
   newtio.c_cc[VSWTC]    = 0;     /* '\0' */
   newtio.c_cc[VSTART]   = 0;     /* Ctrl-q */ 
   newtio.c_cc[VSTOP]    = 0;     /* Ctrl-s */
   newtio.c_cc[VSUSP]    = 0;     /* Ctrl-z */
   newtio.c_cc[VEOL]     = 0;     /* '\0' */
   newtio.c_cc[VREPRINT] = 0;     /* Ctrl-r */
   newtio.c_cc[VDISCARD] = 0;     /* Ctrl-u */
   newtio.c_cc[VWERASE]  = 0;     /* Ctrl-w */
   newtio.c_cc[VLNEXT]   = 0;     /* Ctrl-v */
   newtio.c_cc[VEOL2]    = 0;     /* '\0' */

   /* 
    * clean the serial line and activate the settings for the port
    */
   if (tcflush (po_hi_c_driver_serial_fd_write, TCIOFLUSH) == -1)
   {
192
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcflush()\n");
193
194
195
196
   }

   if (tcsetattr (po_hi_c_driver_serial_fd_write, TCSANOW, &newtio) == -1)
   {
197
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcsetattr()\n");
198
199
   }

200
    __PO_HI_DEBUG_INFO ("[LINUX SERIAL] End of init\n");
201
202
203
204
205
206
207
208
209
210
}
#endif


#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_RECEIVER)
void __po_hi_c_driver_serial_linux_init_receiver (__po_hi_device_id id)
{
   struct termios oldtio,newtio;

211
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Init\n");
212
213
214
215
216

   po_hi_c_driver_serial_fd_read = open( __po_hi_get_device_naming (id), O_RDONLY | O_NOCTTY);

   if (po_hi_c_driver_serial_fd_read < 0)
   {
217
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error while opening device %s\n", __po_hi_get_device_naming (id));
218
219
220
   }
   else
   {
221
      __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Device successfully opened, fd=%d\n", po_hi_c_driver_serial_fd_read);
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
   }

   tcgetattr (po_hi_c_driver_serial_fd_read, &oldtio);  /* save current serial port settings */
   bzero (&newtio, sizeof(newtio));                /* clear struct for new port settings */
        
   /* 
    * BAUDRATE: Set bps rate. You could also use cfsetispeed and cfsetospeed.
    * CRTSCTS : output hardware flow control (only used if the cable has
    *           all necessary lines. See sect. 7 of Serial-HOWTO)
    * CS8     : 8n1 (8bit,no parity,1 stopbit)
    * CLOCAL  : local connection, no modem contol
    * CREAD   : enable receiving characters
    */

   newtio.c_cflag = __PO_HI_DRIVER_SERIAL_LINUX_BAUDRATE | CRTSCTS | CS8 | CLOCAL | CREAD;
         
   /*
    *  IGNPAR  : ignore bytes with parity errors
    *  ICRNL   : map CR to NL (otherwise a CR input on the other computer
    *            will not terminate input) otherwise make device raw 
    *            (no other input processing)
   newtio.c_iflag = IGNPAR | ICRNL;
    */
         
   /*
    * Raw output.
    */
   newtio.c_oflag = 1;
         
   /*
    * ICANON  : enable canonical input
    * disable all echo functionality, and don't send signals to calling program
   newtio.c_lflag = ICANON;
    */

   /* 
    * Initialize all control characters 
    * default values can be found in /usr/include/termios.h, and are given
    * in the comments, but we don't need them here.
    */

   /* 
    * clean the serial line and activate the settings for the port
    */
   if (tcflush (po_hi_c_driver_serial_fd_read, TCIOFLUSH) == -1)
   {
268
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcflush()\n");
269
270
271
272
   }

   if (tcsetattr (po_hi_c_driver_serial_fd_read, TCSANOW, &newtio) == -1)
   {
273
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcsetattr()\n");
274
275
   }

276
    __PO_HI_DEBUG_INFO ("[LINUX SERIAL] End of init\n");
277
278
279
280
281
}
#endif


#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX)
282

283
void __po_hi_c_driver_serial_linux_init (__po_hi_device_id id)
284
{
285
286
   struct termios oldtio,newtio;

287
   __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Init\n");
288

289
   po_hi_c_driver_serial_fd_read = po_hi_c_driver_serial_fd_write = open( __po_hi_get_device_naming (id), O_RDWR | O_NOCTTY | O_NONBLOCK);
290

291
   if (po_hi_c_driver_serial_fd_read < 0)
292
   {
293
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error while opening device %s\n", __po_hi_get_device_naming (id));
294
   }
295
296
   else
   {
297
      __PO_HI_DEBUG_INFO ("[LINUX SERIAL] Device successfully opened, fd=%d\n", po_hi_c_driver_serial_fd_read);
298
   }
299

300
   tcgetattr (po_hi_c_driver_serial_fd_read, &oldtio);  /* save current serial port settings */
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
   bzero (&newtio, sizeof(newtio));                /* clear struct for new port settings */
        
   /* 
    * BAUDRATE: Set bps rate. You could also use cfsetispeed and cfsetospeed.
    * CRTSCTS : output hardware flow control (only used if the cable has
    *           all necessary lines. See sect. 7 of Serial-HOWTO)
    * CS8     : 8n1 (8bit,no parity,1 stopbit)
    * CLOCAL  : local connection, no modem contol
    * CREAD   : enable receiving characters
    */

   newtio.c_cflag = __PO_HI_DRIVER_SERIAL_LINUX_BAUDRATE | CRTSCTS | CS8 | CLOCAL | CREAD;
         
   /*
    *  IGNPAR  : ignore bytes with parity errors
    *  ICRNL   : map CR to NL (otherwise a CR input on the other computer
    *            will not terminate input) otherwise make device raw 
    *            (no other input processing)
    */
   newtio.c_iflag = IGNPAR | ICRNL;
         
   /*
    * Raw output.
    */
325
   newtio.c_oflag = 1;
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
         
   /*
    * ICANON  : enable canonical input
    * disable all echo functionality, and don't send signals to calling program
    */
   newtio.c_lflag = ICANON;

   /* 
    * Initialize all control characters 
    * default values can be found in /usr/include/termios.h, and are given
    * in the comments, but we don't need them here.
    */
   newtio.c_cc[VINTR]    = 0;     /* Ctrl-c */ 
   newtio.c_cc[VQUIT]    = 0;     /* Ctrl-\ */
   newtio.c_cc[VERASE]   = 0;     /* del */
   newtio.c_cc[VKILL]    = 0;     /* @ */
   newtio.c_cc[VEOF]     = 4;     /* Ctrl-d */
   newtio.c_cc[VTIME]    = 0;     /* inter-character timer unused */
   newtio.c_cc[VMIN]     = 1;     /* blocking read until 1 character arrives */
   newtio.c_cc[VSWTC]    = 0;     /* '\0' */
   newtio.c_cc[VSTART]   = 0;     /* Ctrl-q */ 
   newtio.c_cc[VSTOP]    = 0;     /* Ctrl-s */
   newtio.c_cc[VSUSP]    = 0;     /* Ctrl-z */
   newtio.c_cc[VEOL]     = 0;     /* '\0' */
   newtio.c_cc[VREPRINT] = 0;     /* Ctrl-r */
   newtio.c_cc[VDISCARD] = 0;     /* Ctrl-u */
   newtio.c_cc[VWERASE]  = 0;     /* Ctrl-w */
   newtio.c_cc[VLNEXT]   = 0;     /* Ctrl-v */
   newtio.c_cc[VEOL2]    = 0;     /* '\0' */

   /* 
    * clean the serial line and activate the settings for the port
    */
359
   if (tcflush (po_hi_c_driver_serial_fd_read, TCIOFLUSH) == -1)
360
   {
361
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcflush()\n");
362
363
   }

364
   if (tcsetattr (po_hi_c_driver_serial_fd_read, TCSANOW, &newtio) == -1)
365
   {
366
      __PO_HI_DEBUG_CRITICAL ("[LINUX SERIAL] Error in tcsetattr()\n");
367
   }
368

369
    __PO_HI_DEBUG_INFO ("[LINUX SERIAL] End of init\n");
370
}
371
372
373
374
375
#endif


#if defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX) || \
    defined (__PO_HI_NEED_DRIVER_SERIAL_LINUX_SENDER)
376

377
int  __po_hi_c_driver_serial_linux_sender (__po_hi_task_id task_id, __po_hi_port_t port)
378
{
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
   int n;
   int ts;
   unsigned long* swap_pointer;
   unsigned long swap_value;
   __po_hi_local_port_t local_port;
   __po_hi_request_t* request;
   __po_hi_msg_t msg;
   __po_hi_port_t destination_port;

   local_port = __po_hi_get_local_port_from_global_port (port);

   request = __po_hi_gqueue_get_most_recent_value (task_id, local_port);

   destination_port     = __po_hi_gqueue_get_destination (task_id, local_port, 0);

   __po_hi_msg_reallocate (&msg);

   request->port = destination_port;

398
   __po_hi_marshall_request (request, &msg);
399

400
401
402
403
   /* Swap only the port (first 32 bytes) */
   swap_pointer  = (unsigned long*) &msg.content[0];
   swap_value    = *swap_pointer;
   *swap_pointer = __po_hi_swap_byte (swap_value);
404

405
   n = write (po_hi_c_driver_serial_fd_write, &msg, __PO_HI_MESSAGES_MAX_SIZE);
406

407
#ifdef __PO_HI_DEBUG_INFO
408
   __PO_HI_DEBUG_INFO  ("[LINUX SERIAL] Message sent: 0x");
409

410
411
   for (ts = 0 ; ts < __PO_HI_MESSAGES_MAX_SIZE ; ts++)
   {
412
      __PO_HI_DEBUG_INFO ("%x", msg.content[ts]);
413
   }
414
   __PO_HI_DEBUG_INFO ("\n");
415
#endif
416

417
   return 1;
418
}
419
#endif
420

421
#endif